S-I
Seal and Groove Dimensions in Millimeters (mm) | ||||||||||||||
Seal Height |
Tolerance |
Seal Width |
Seal Diameter Range |
Sheet Thickness |
Seal & Groove Clearance | Groove Height |
Groove Corner Radius
|
Groove Width |
Spring Back Values (mm)
|
Load Values N/mm Circumference
|
||||
SH | T | SW | SDR | ST | SGC | GH | GR | GW | ||||||
L | T | L | T | L | T | |||||||||
00.79 |
(+/-0.05) |
0.71 |
6-25 |
0.13 |
0.18 |
0.08 |
0.65-0.70 |
0.25 |
1.02 |
0.04 |
0.03 |
31 |
66 |
|
01.19 |
(+/-0.05) |
0.96 |
8-50 |
0.13 |
0.20 |
0.13 |
0.94 - 1.02 |
0.30 |
1.40 |
0.05 |
0.04 |
22 |
52 |
|
01.57 |
(+/-0.05) |
01.26 |
10-200 |
0.15 |
0.25 |
0.15 |
1.27 - 1.37 |
0.38 |
1.91 |
0.08 |
0.06 |
22 |
62 |
|
02.00 |
(+/-0.05) |
01.60 |
13-200 |
0.25 |
O.R |
0.20 |
1.60 - 1.68 |
0.45 |
2.30 |
0.06 |
O.R |
44 |
O.R |
|
02.20 |
(+/-0.05) |
01.76 |
13-200 |
0.25 |
O.R |
0.22 |
1.76 - 1.85 |
0.47 |
2.50 |
0.08 |
O.R |
45 |
O.R |
|
02.39 |
(+/-0.05) |
01.91 |
13-400 |
0.25 |
0.38 |
0.24 |
1.91 - 2.01 |
0.51 |
2.67 |
0.10 |
0.08 |
46 |
97 |
|
02.79 |
(+/-0.05) |
02.25 |
20-400 |
0.38 |
O.R |
0.28 |
2.23 - 2.34 |
0.55 |
3.10 |
0.12 |
O.R |
71 |
O.R |
|
03.18 |
(+/-0.08) |
02.54 |
30-600 |
0.38 |
0.51 |
0.32 |
2.54 - 2.67 |
0.76 |
3.43 |
0.15 |
0.13 |
56 |
107 |
|
03.60 |
(+/-0.08) |
02.88 |
45-600 |
0.41 |
O.R |
0.36 |
2.88 - 3.02 |
0.90 |
3.90 |
0.12 |
O.R |
51 |
O.R |
|
03.96 |
(+/-0.08) |
03.17 |
45-750 |
0.41 |
0.61 |
0.39 |
3.18 - 3.30 |
1.27 |
4.32 |
0.20 |
0.17 |
46 |
117 |
|
04.40 |
(+/-0.08) |
03.52 |
75-800 |
0.41 |
O.R |
0.44 |
3.52 - 3.69 |
1.27 |
4.70 |
0.21 |
O.R |
41 |
O.R |
|
04.78 |
(+/-0.10) |
03.82 |
75-900 |
0.51 |
0.76 |
0.47 |
3.84 - 3.99 |
1.27 |
5.08 |
0.22 |
0.18 |
8] |
147 |
|
05.00 |
(+/-0.10) |
04.01 |
75-900 |
0.51 |
O.R |
0.50 |
4.00 - 4.20 |
1.27 |
5.30 |
0.23 |
O.R |
56 |
O.R |
|
05.20 |
(+/-0.10) |
04.16 |
75-900 |
0.51 |
O.R |
0.52 |
4.16 - 4.37 |
1.27 |
5.50 |
0.23 |
O.R |
57 |
O.R |
|
05.60 |
(+/-0.10) |
04.50 |
75-1000 |
0.51 |
O.R |
0.56 |
4.48 - 4.70 |
1.27 |
5.90 |
0.22 |
O.R |
51 |
O.R |
|
06.35 |
(+/-0.10) |
05.08 |
100-1200 |
0.64 |
0.97 |
0.64 |
5.08 - 5.28 |
1.52 |
6.60 |
0.30 |
0.27 |
66 |
177 |
|
07.90 |
(+/-0.10) |
06.32 |
100-1500 |
0.97 |
O.R |
0.79 |
6.32 - 6.58 |
1.52 |
8.22 |
0.30 |
O.R |
131 |
O.R |
|
09.53 | (+/-0.10) |
07.62 |
300-2000 |
0.97 |
1.27
|
0.96 |
7.62 - 8.03 |
1.52 |
9.65 |
0.40 |
O.32 |
102 |
187 |
|
012.70 |
(+/-0.13) |
10.16 |
600-3000 |
1.27 |
1.65 |
01.27 |
10.16-10.67 |
1.52 |
12.70 |
0.55 |
0.48 |
126 |
231 |
Note: Above given values are based on lab setup conditions especially the Load and Spring-Back values. Practically the values can differ based on the actual seal size, groove conditions, groove dimensions, surface finish and seal plating conditions.