T-O / T-DO / T-GO / T-SO
Seal and Groove Dimensions in Millimeters (mm) | ||||||||||||
Seal Height | Seal Tolerance | Seal Diameter Range | Wall Thickness | Seal & Groove Clearance | Groove Heigh | Groove Corner Radius | Groove Width | Spring Back Values (mm) | Load Values N/mm Circumference | |||
SH | SD | ST | SGC | GH | GR | GW | L | T | L | T | ||
L | T | |||||||||||
00.89 |
(+0.08/-0.03) |
6-25 |
0.15 |
- |
0.20 |
0.64-0.69 |
0.25 |
1.40 |
0.01 |
- |
67 |
- |
01.19 |
(+0.08/-0.03) |
10 - 50 |
- |
0.20 |
0.25 |
0.94-1.02 |
0.30 |
1.78 |
0.03 |
- |
- |
81 |
01.57 |
(+0.08/-0.03) |
12 - 200 |
0.25 |
0.36 |
0.28 |
1.14 - 1.27 |
0.38 |
2.29 |
0.03 |
0.03 |
102 |
222 |
02.39 |
(+0.08/-0.03) |
25 - 220 |
0.25 |
0.46 |
0.33 |
1.88 - 2.01 |
0.51 |
3.18 |
0.05 |
0.03 |
57 |
202 |
03.18 |
(+0.08/-0.03) |
50 - 400 |
0.25 |
0.51 |
0.43 |
2.54-2.67 |
0.76 |
4.06 |
0.07 |
0.04 |
36 |
161 |
03.96 |
(+0.10) |
75 - 650 |
0.41 |
0.51 |
0.61 |
3.18 - 3.30 |
1.27 |
5.08 |
0.10 |
0.08 |
72 |
114 |
04.78 |
(+0.13) |
100 - 800 |
0.51 |
0.64 |
0.71 |
3.84 - 3.99 |
1.27 |
6.35 |
0.10 |
0.08 |
91 |
151 |
06.35 |
(+0.13) |
200 - 1200 |
0.64 |
0.81 |
0.76 |
5.05-5.28 |
1.52 |
8.89 |
0.20 |
0.10 |
102 |
182 |
09.53 |
(+0.13) |
300 - 2000 |
0.97 |
1.24 |
1.02 |
8.26 - 8.51 |
1.52 |
12.70 |
0.15 |
0.12 |
163 |
281 |
12.70 |
(+0.15) |
800 - 3000 |
1.27 |
1.65
|
1.27 |
11.05 - 11.43 |
1.52 |
16.51 |
0.22 |
0.18 |
202 |
366 |
Note: Above given values are based on lab setup conditions especially the Load and Spring-Back values. Practically the values can differ based on the actual seal size, groove conditions; groove dimensions surface finish and seal plating conditions. Also do not refer the Load and Spring Back values for spring energized o-rings.